Low Prices and Fast Shipping
Proper tank pressure (7 PSI) must be maintained for the hydraulic functions of the water to work correctly within the RO system. Tank bladders can lose air pressure just like a tire looses air pressure. To monitor your system's air tank pressure to help insure proper system operation we suggest a SPECIALLY CALIBRATED AIR PRESSURE GAUGE.
CHECK YOUR TANK'S AIR PRESSURE:1. Turn off the RO system's inlet water line.2. Open the faucet and allow the water to run until the flow stops. Close the faucet.3. Turn off the tank valve.4. Lift the tank. Is it heavy like it has water in it? About the weight of a bowling ball? (If the answer is yes, replace the tank)5. Check the air pressure of the tank. There is an air stem on the tank similar to the ones on a tire. They are usually covered with a rubber or plastic cap to protect them. You must remove the cap to expose the air stem.6. Inflate or deflate tank to reach the desired 7 PSI air pressure. You can use a standard air pump similar to a bike pump or compressor. Easy does it with the compressor, this is a low pressure system. Do not over inflate and damage the air bladder.7. Open the tank valve.8. Open the inlet water valve.9. Allow the tank to fill. This may take a few hours. Once filled, see if the system now operates correctly after you corrected the air pressure. If not, see the following:
RUPTURED AIR BLADDER IN TANK:The other problem is that Reverse Osmosis tank bladders frequently fail, requiring replacement of the tank. If the bladder in the tank starts to leak water into the air side of the bladder, the tank will have to be replaced. Open the faucet and drain all of the water from the tank. Pick up the tank. If the tank feels heavy like it is full even though you can't get water out of the faucet, the bladder is ruptured. Also, as this happens the air stem sometimes may be wet, or the air valve may even rust from water that passed to the air side of the bladder. Lift the tank when empty and hold it upside down so that the air stem is at the very lowest point on the tank. Then discharge some air from the air valve. Did you get any water? If so, the tank must be replaced. Another problem is that the air valve may leak air just like a bike or car tire. Air valves leaking air is actually is a very common failure. See Replacement RO Tanks.
Inversion Stand for Water Tank on Reverse Osmosis Systems. Flip the tank over and remove the weight of the water from the bladder. Pressure and storage capacity are unchanged. Extends the life of your reverse osmosis water tank.
Inline Water Shut Off Valve - Great For Refrigerators, Ice Machines, reverse osmosis systems and under counter drinking water systems. Built in quick connectors. Very easy to install and use.
Quick Fittings and Connector Instructions
John Guest PI0208S Union Tee 1/4" Tube X 1/4" Tube X 1/4" Tube for Drinking Water Systems
4 Gallon Reverse Osmosis Tank GGN-Tank-4 Pro 3.2. This is the perfect replacement tank for most RO reverse osmosis systems. Stainless Steel valve connector. Perfect replacement for all home RO reverse osmosis drinking water systems.
SS Stainless Steel Reverse Osmosis 4.4 Gallon Total Capacity Tank
This is one of the finest RO tanks we have ever seen. The patented O-ring seal on the air stem assures "set and forget" pressure settings. Keeping the pressure in the tank set correctly is an important factor in operating your RO system. Approximately 14" high (without the tank valve) X 11" in diameter.
John Guest ® Poly Tubing 1/4" For Pure Drinking Filter Water Systems
Premium inline reverse osmosis membrane flow restrictor - Keep your system operating correctly by replacing worn flow restrictors. Reverse Osmosis systems use pressure differencials to power the reverse osmosis process. A worn flow restrictor will alter the proper balance. Our in-line capillary flow restrictors are very simple to install.
Be sure to check our for important parts such as , , , , , , , and more parts for your reverse osmosis pure water filtration system. View maintenance and servicing tips online at our Installation & Trouble shooting Guide.
Starting at $5.99